ohsetr.blogg.se - Deck rails

Deck rails how to#
Deck rails plus#

Here are various railing materials and how to safely clean them: Each material responds best to a certain kind of cleaning solution and routine. Clean with the right suppliesĭeck railings come in a variety of materials, including wood, composite, aluminum and vinyl.

No matter what material your deck railing is made of, you can keep it in good shape season after season. That way, just about anything you could splatter with cleaners will be safe. Working bottom up ensures that the areas below are wet, so cleaning solution is less likely to leave marks.īy this same logic, wash your deck before hitting the railings but make sure to dampen the railing during this process. Some cleaning solutions can discolor wood decks if splashed on a dry spot. This method prevents you from splattering the cleaning solution on a dry area of your railing. When you do wash your railings, begin the process near the base and work your way up. Doing both at the same time makes getting all the corners easier, helps you remember to get the railings, and ensures both deck components look the same – if one has more dirt than the other, you may be able to see the difference. This should happen a couple of times a year with a few spot-cleaning sessions in between. Whenever you clean your deck, also get the railings. With that in mind, here are some tips for maintaining your deck railings so they serve you for years to come: Wash them with your deck As they say: “An ounce of prevention is worth a pound of cure.” This is certainly true for any building material, including deck railings. Developing a few care habits will help you keep your railings in as good condition as when you initially installed them. And with so many styles available, railings also provide a unique touch. 2 September 2020.Deck railings are easy to install, make your deck a safe place, and add a touch of refinement to your yard. This prevents water from entering at the top.

If the posts will be higher than the railing (the railings will not be nailed to the tops of the posts), nail a metal or wooden post cap onto the top of the railing.

Drill 1⁄ 2 in (1.3 cm) holes through the post and the board behind it. Washers are used only on the ends of the bolts with the nuts.

If you will use lag bolts, use two 1⁄ 2 in (1.3 cm)-diameter galvanized lag bolts with waters and nuts.

Drill 1⁄ 2 in (1.3 cm) holes through the post, followed by 3⁄ 8 in (0.95 cm) pilot holes into the board behind the post." X Research source If you will be using lag screws, Brant advises "using two 1⁄ 2 in (1.3 cm)-diameter galvanized screws with washers, which are rust-proof. Then, drill lag screws or carriage bolts into the pilot holes. Handyman Walter Brant suggests "holding a post in the position where it will be mounted and using a large level to hold it in a vertical position." Next, use a drill to form pilot holes through the overhang of the posts into the deck joists.

Many people like to leave about 1.5 inches (3.8 cm) or so between the bottom railing and the deck boards as well, so factor this into the post height as well.

For instance, if your deck is made of boards that are 1 inch (2.5 cm) thick and the supports are 6 inches (15 cm) high, then you'll want your posts to be long enough to hang up to 7 inches (18 cm) but at least 4 inches (10 cm) below the railing

You'll need enough length hanging below the surface of the deck to attach the posts securely to the supports.

An inch or two higher than the railing will look nice.

The posts' extra height above the railing is just for looks.

Most building codes require deck railings to be between 36 inches (91 cm) and 42 inches (110 cm) high.

For instance, if you want a railing that is 36 inches (91 cm) high, cut posts that are perhaps 44 inches (110 cm) high.

Deck rails plus#

Cut 4x4s to be at least a little higher than the railing will be, plus extra length to hang below the deck planks.